White Rodgers Packaged Unit/RTU Parts

Universal Gas Valve, HSI/DSI Single Stage, Slow Opening, Inlet / Outlet Pressure Taps, Plastic Hose Barb (For Connection To ¼ Hose/Flexible Tubing), LP Gas Conversion Kit, Inlet/Outlet Reducer Bushings (1/2 NPT X 3/8 NPT) 100KBTU/Hr (Nat Gas), 24V, 60 Hz, 1/2 X 1/2 NPT, Replaces 36G24-214

Manufacturer #36J24-214

Universal Integrated Ignition Module

Manufacturer #50A55-843S1

This is universal kit, depending on your original control board, you may need to bypass the rollout. Jumper wire is included.

Replacement control board for Goodman and Amana part number PCBBF132S.

Manufacturer #50M56-743

Hot Surface Ignitor With 5-1/4" Leads, N Style Mounting Block, Left Tab, Insulation 200°C, Electrical Connection, Molex Side Lock Connector with .092” Male Pins, Replaces R/S 41-408

Manufacturer #767A-372

If the electrical connnector on your old part is different than the new igniter, it can be cut off and spliced onto the new igniter wires using the provided wire nuts.

Universal hot surface ignition control

Manufacturer #50E47-843S1

Hot Surface Ignitor with 5-1/4" Leads, NM Style Mounting Block, right tab, Insulation 200°C, Connector with Brackets, Includes Ceramic Wire Nuts. Replaces R/S 41-414

Manufacturer #767A-384

If the electrical connnector on your old part is different than the new igniter, it can be cut off and spliced onto the new igniter wires using the provided wire nuts.

Universal Gas Valve - *The Manufacture recommends that this part be installed by a licensed contractor.

Manufacturer #36G22-254

Hot Surface Ignitor

Manufacturer #768A-815

If the electrical connnector on your old part is different than the new igniter, it can be cut off and spliced onto the new igniter wires using the provided wire nuts.

Furnace control board kit. This single stage control board is designed to replace Lennox part number 83M00 and Y7761. The control board regulates the supply of power to the furnace components. Be sure to test more commonly defective parts before replacing the control board.

Manufacturer #21D83M-843

Hot Surface Ignitor With 5-1/2" Leads, A Style Mounting Block, Sealed Combustion, Insulation 200°C, Electrical Connection, Molex Internal Keyed Connector with .093" Male Pins, Includes Gasket, Replaces R/S 41-401

Manufacturer #767A-369

If the electrical connnector on your old part is different than the new igniter, it can be cut off and spliced onto the new igniter wires using the provided wire nuts.

Hot Surface Ignitor With 5.25" Leads, 200° Insulation, Electrical Connection Receptacle with .093" Male Pins, Replaces R/S 41-405

Manufacturer #767A-361

If the electrical connnector on your old part is different than the new igniter, it can be cut off and spliced onto the new igniter wires using the provided wire nuts.

Hot Surface Ignitor Mini With 7.5" (+/- 1") Leads Including Electrical Connector. Replaces R/S 41-603

Manufacturer #767A-379

If the electrical connnector on your old part is different than the new igniter, it can be cut off and spliced onto the new igniter wires using the provided wire nuts.

Hot Surface Ignitor With 5-1/4" Leads, M Style Mounting Block, Insulation 200°C, Electrical Connection, Receptacle with .093" Male Pins, Connector with Mounting Adaptor, Replaces R/S 41-404

Manufacturer #767A-382

If the electrical connector on your old part is different than the new igniter, it can be cut off and spliced onto the new igniter wires using the provided wire nuts.