GO
SEARCH:

Haier Air Conditioner Compressor Won't Run

The part(s) or condition(s) listed below for the symptom Air conditioner compressor won't run are ordered from most likely to least likely to occur. Check or test each item, starting with the items at the top of the page.

Most Frequent Causes for Air conditioner compressor won't run

For the most accurate results, enter your model number.


Cause 1Incoming Power Problem

Confirm the air conditioner is plugged in and there is power at the wall receptacle. If it has a 120 volt outlet, you can plug another small appliance into the recepticle to confirm there is power. For 220 volt units you will need to use a multimeter. If there is no power, confirm the circuit breaker has not tripped. Most air conditioners will have a seperate breaker on the power cord plug. Confirm this breaker is not tripped. If the blower motor is working the unit has power.

Cause 2Temperature Control Thermostat

The temperature control thermostat has electrical contacts inside that burn out over time. It is possible for the thermostat to still turn on the fan motor but not the compressor motor.

Parts
Cause 3Temperature Control Board

The temperature control board provides voltage to the fan motor and compressor. If the control board is defective, it may stop providing voltage to the compressor. Control boards are often misdiagnosed. Before replacing the temperature control board, make sure you check more commonly defective parts—particularly the compressor overload, capacitor and the compressor itself. If you are certain that all of the other components are working properly, replace the temperature control board.

Parts
Cause 4Thermostat

The thermostat monitors the temperature of the air. When the air temperature rises above a set point, the thermostat activates a switch to provide power to the fan and compressor. If the thermostat is defective, it may prevent the compressor from running. If you determine that the compressor is at fault, replace it.

Parts
Cause 5Overload

The overload protects the compressor from burning out if it draws too much current. Over time, the overload can burn out. To determine if the overload is burned out, use a multimeter to test the overload for continuity. If the overload does not have continuity, replace it.

Parts
Cause 6Compressor

The compressor itself might be defective. However, this is not usually the case. Before replacing the compressor, be sure to check more commonly defective components—particularly the overload protector and the compressor capacitor. If the compressor is defective, it should only be replaced by a licensed technician.

Parts
Cause 7Thermistor

The thermistor is a sensor connected to the control board that detects the temperature of the outside air. If the thermistor does not have continuity, it can prevent the compressor from running. To determine if the thermistor is at fault, use a multimeter to test it for continuity. If the thermistor does not have continuity, replace it.

Parts
Cause 8Relay Board

The relay board provides voltage to many of the components of the air conditioner. If the board is defective, it can stop sending voltage to the compressor. Relay boards are often misdiagnosed; before replacing the board, make sure you check more commonly defective parts—particularly the overload protector, the compressor capacitor, and the compressor itself. If you are certain that all of the other components are working properly, replace the relay board.

Parts
Cause 9Main Control Board

The main control board provides voltage to all of the components of the air conditioner. If there is a problem with the main control board, it might not send voltage to the compressor. However, this is rarely the case. Before replacing the board, make sure you check more commonly defective components—particularly the overload protector, compressor capacitor, and the compressor itself. If you are certain that all of the other components are working properly, replace the main control board.

Parts
Cause 10Run Capacitor

A run capacitor is the component that powers the compressor. If the capacitor burns out, the compressor will not run. To determine whether the capacitor is burned out, use a multimeter to test it for continuity. If the capacitor does not have continuity, replace it.

Parts
Cause 11Capacitor

The capacitor is attached to the compressor by electrical leads. If the capacitor burns out, the compressor won’t run. To determine whether the capacitor is burned out, use a multimeter to test it for continuity. If the capacitor does not have continuity, replace it.

Parts
Cause 12Dual Run Capacitor

A dual run capacitor will power both the compressor and the fan motor. If the capacitor burns out, the compressor will not run. To determine whether the capacitor is burned out, use a multimeter to test it for continuity. If the capacitor does not have continuity, replace it.

Parts
Cause 13Selector Switch

The selector switch directs voltage to the compressor. If the selector switch is defective, the compressor won’t run. First, check the capacitor, overload, and the compressor itself. If none of these parts are defective, the selector switch might be at fault. If the compressor runs intermittently when you press the selector buttons or rotate the switch knob, replace the selector switch.

Parts
Cause 14Start Relay

The start relay works in conjunction with the start winding to start the compressor. If the start relay is defective, the compressor may sometimes fail to run or may not run at all. As a result, the air conditioner will not be cold enough. To determine if the start relay is defective, use a multimeter to test it for continuity between the run and start terminal sockets. If the start relay does not have continuity between the run and start terminal sockets, replace it. In addition, if the start relay has a burnt odor, replace it.

Parts